Karcher IP 120 Manual do Utilizador descarregar pdf (Página 13)

English 13

몇

Warning

Installation sets must only be installed by

authorized personnel.

 Danger

Risk of injury on account of electric shock.

Pull the plug out of the socket before open-

ing the control cabinet.

Î Open the switch cabinet locks, swivel

cover upward and latch.

1Lock

2Nut

3Cover

Î Remove the nuts on the cover.

Î Remove cover.

Î Insert the control and fasten it with

screws.

1 Dummy connector

2 Power strip

Î Pull the dummy connector out of the

power strip.

Î Insert the control plug instead of the

dummy connector.

Î Install the scale platform below the pel-

let ejector and level.

Note

Make sure that the scale platform is free-

standing and not obstructed by any objects,

as this will cause inaccurate measure-

ments.

Î Open both latches on the front machine

cover.

Î Tilt the cover toward the outside and lift

off from the top.

1Plug

Î Guide the scale platform cable into the

machine from the bottom and connect

the plug on the bottom of the switch

cabinet.

Î Close and lock the machine cover.

The volume control is installed just like the

control of the installation set "Scale".

The scale does not need to be connected.

 Danger

Risk of suffocation on account of carbon di-

oxide. The carbon dioxide content in the air

at the place where the machine is used will

increase when the machine is running. En-

sure adequate ventilation at the place of

use; if possible, use an alarm to warn per-

sons. Symptoms of high levels of carbon di-

oxide in the air that is breathed in:

– 3...5%: headache, faster breathing.

– 7...10%: headache, nausea and per-

haps even unconsciousness.

If any of these symptoms occur, please

switch off the machine immediately and get

a breath of fresh air and improve the venti-

lation before starting work again with the

machine.

Follow the safety specifications of the man-

ufacturer of carbon dioxide.

 Danger

Risk of cold burns. Dry ice has a tempera-

ture of -79 °C. Never touch dry ice or cold

parts of the machine without appropriate

protection. Wear protective gloves and pro-

tective overalls.

 Danger

Risk of injury on account of ejected dry ice

pellets. Inspect the pellet ejector for cleanli-

ness prior to taking it into operation. Do not

look directly at the extruder plate.

 Danger

Danger of bursting. Never store dry ice in

tightly sealed containers.

Î Set the key switch "M/0/A" to "A". Re-

move the key and store so that it can

only be accessed by service personnel.

Î Switch on the power supply.

Î Open the carbon dioxide supply.

Î Turn on the main switch.

Î Release emergency-stop button by

turning.

The indicator lamp "Voltage on" will illu-

minate.

Î Place an empty container below the pel-

let ejector.

Î If the installation set "Scale" has been

installed, set the key switch "On/Off" to

"Off".

Î If the installation set "Volume control"

has been installed, set the key switch

"Direct/PCS" to "Direct".

Î Press "On" key.

The pellet production will start.

Î Once the desired quantity of pellets has

been produced, press the "Off" key.

The machine will finish the current pro-

duction cycle and will then terminate the

pellet production.

In automatic mode, a preset quantity of pel-

lets is produced. After that, the machine will

terminate the pellet production.

1Display

2 "F" key

Î Set the key switch "0/OFF" / "I/ON" to

"1/ON" (option).

Î Center an empty container on the scale

platform.

Î Read its empty weight (in kg) on the dis-

play.

Î Press "F" key.

Î Set its empty weight (in kg) on the dis-

play using the arrow keys.

Î Press "F" key until "CF" is shown on the

display.

Î Release the "F" key and press it once

again.

The display shows "H1" and the set

empty weight (alternating).

Î Set the pellet quantity to be produced

(in kg) on the display using the arrow

keys.

Î Press "F" key until the empty weight is

shown on the display.

Install attachment sets

Mounting the installation set scale

(option)

Installing the control

Connecting the scale

Mounting the installation set "Vol-

ume control PCS" (option)

Operation

Start up

Manual operation

Automatic operation with the instal-

lation set "Scale" (option)

Setting the quantity to be produced

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 156 157

Comentários a estes Manuais

Sem comentários

Karcher IP 120 Manual do Utilizador Página 13

Comentários a estes Manuais

Manuais e produtos relacionados com Equipamento Karcher IP 120